pycom - Go Invent

FiPy - With headers

Art.nr: FiPy
959 Kr
Lagerstatus: 11
Leveranstid: 1-3 Vardagar
Ej betygsatt ännu

Imagine 5 networks in one perfectly-formed, same-small-foot-print-as-WiPy- LoPy-and SiPy, IoT development board. MicroPython enabled. Featuring WiFi, Bluetooth, LoRa, Sigfox and dual LTE-M (CAT M1 and NBIoT) the FiPy gives access to all the world’s LPWAN networks on one tiny board.


  • Tipsa
    Tipsa en vän
  • Önska
Dela:

Note: The LTE Antenna MUST always be used with LTE CAT M1 / NB1, or it could cause serious damage to the development board.

Imagine 5 networks in one perfectly-formed, same-small-foot-print-as-WiPy- LoPy-and SiPy, IoT development board. MicroPython enabled. Featuring WiFi, Bluetooth, LoRa, Sigfox and dual LTE-M (CAT M1 and NBIoT) the FiPy gives access to all the world’s LPWAN networks on one tiny board.

Get on with a board that gives you full flexibility during testing, install, deployment and even later when you want to switch real-time your airtime network provider. You can switch when the time is right for you or set some parameters that will do so automatically.


Gpy Features:

– Powerful CPU, BLE and state of the art WiFi radio. 
– 1KM WiFi range
– MicroPython enabled
– Fits in a standard breadboard (with headers)
– Ultra-low power usage: a fraction compared to other connected micro controllers


LTE-M Operating Frequencies

– 34 bands supported from 699Mhz to 2170Mhz (Total world-wide support)


LTE-M Specification

– One single chip for both CAT M1 and NB1
– 3GPP release 13 LTE Advanced Pro
– Supports narrowband LTE UE categories M1/NB1
– Integrated baseband, RF, RAM memory and power management
– Reduced Tx power class option
– Peak power estimations: TX current = 420mA peak @1.5Watt RX current = 330mA peak @1.2Watt
– Data rates:
– 300kbps DL
– 375 kbps UL (LTE Cat M1 in 1.4Mhz in 1.4 Mhz, HD-FDD) – 40 kbps DL
– 55kbps UL (LTE Cat M2 in 200 kHz, HD-FDD)


Processing

– Espressif ESP32 chipset
– Dual processor + WiFi radio System on chip
– Network processor handles the WiFi connectivity and the IPv6 stack
– Main processor is entirely free to run the user application
– An extra ULP-coprocessor that can monitor GPIOs, the ADC channels and control most of the internal peripherals during deep-sleep mode while only consuming 25uA


Interfaces

– 2 x UART, 2 x SPI, I2C, I2S, micro SD card
– Analog chnnels: 8×12 bit ADCs
– Timers: 4×16 bit with PWM and input capture
– DMA on all peripherals
– GPIO: Up to 22


Memory

– RAM: 4MB
– External flash: 8MB
– Hardware floating point acceleration
– Python multi-threading


WiFi
802.1b/g/n 16mbps

Bluetooth Networking
– Low energy and classic
– Compliant with Bluetooth v4.2 BR/EDR and BLE specification
– Class-1, Class-2 and Class-3 transmitter without external power amplifer
– Enhanced power control
– +10dBm transmitting power
– NZIF receiver with -98 dBm sensitivity
– Adaptive Frequency Hopping (AFH)
– Standard HCI based on SDIO/SPI/UART
– High speed UART HCI, up to 4 Mbps
– BT 4.2 controller and host stack
– Service Discover Protocol (SDP)
– General Access Profile (GAP)
– Security Manage Protocol (SMP)
– Bluetooth Low Energy (BLE)
– ATT/GATT
– HID
– All GATT-based profile supported
– SPP-Like GATT-based profile
– BLE Beacon
– A2DP/AVRCP/SPP, HSP/HFP, RFCOMM
– CVSD and SBC for audio codec
– Bluetooth Piconet and Scatternet

LoRa Operating Frequencies
– 868MHz(Europe) at +14dBm maximum
– 915MHz (North and South America, Australia and New Zealand) at +20dBm maximum


LoRa Specification
– Power consumption: 10mA Rx, 28mA Tx
– LoRaWAN stack
– Class A and C devices
– Node range: Up to 40km
– Nano-gateway: Up to 22km (Capacity up to 100 nodes)



Sigfox Operating Frequencies

RCZ1 – 868MHz(Europe)


Sigfox Specification
– TI CC1125NarrowbandTransceiver
– Class 0 device. Maximum Tx power:
  – +14dBm (Europe)
  – +22dBm (America)
  – +22dBm (Australia and New Zealand)
– Node range: Up to 50km
– Sigfox pre-certified (October 2016)
– Power
  – Sigfox (Europe): 17mA in Rx mode, 47mA in Tx mode and 0.5uA in standby
  – Sigfox (Australia, New Zealand and South America): 24mA in rX mode, 257 mA in Tx mode and 0.5uA in standby




RTC
Running at 32KHz

Power
– Input: 3.3V – 5.5V
– 3v3 output capable of sourcing up to 400mA
– WiFi: 12mA in active mode, 5uA in standby
– Sigfox (Europe): 12mA in Rx mode, 42mA in Tx mode and 0.5uA in standby


Size
55mm x 20mm x 3.5mm (Without Headers)

Weight
– 7g
– 31g (Packaged)

Omdömen (0)
Du måste logga in för att kunna skriva omdömen Logga in
  • Inga omdömen har lämnats för denna produkt

    Bli först med att skriva ett!